Integrated Preparation and Performance Study of Spiral Antenna Based on Modified Polyetheretherketone

doi:10.3969/j.issn.1671-0940.2024.03.003

Abstract

Abstract: This paper introduces an integrated design and manufacturing technology for L-band spiral antennas based on modified polyetheretherketone (PEEK). Initially, PEEK granules are blended with a laser activator for granulation and filamentation, and the antenna structure is fabricated using a fused deposition modeling (FDM) forming device. Subsequently, a pulsed infrared laser with a wavelength of 1064 nm is employed to etch spiral microstrips and feed network board circuit functional patterns on the surface of the formed PEEK material structure. Combined with electroless plating technology, metallization of the spiral lines on the PEEK surface and the feed network board circuitare achieved. Test results demonstrate that the integrated spiral antenna exhibits a standing wave ratio of 1.46 at a frequency of 1.575 GHz, with a gain of ≥-2 dBi within a range of ±70°, and a gain of ≥-4 dBi within a range of ±85°, essentially meeting the antenna specifications. The study indicates that this method holds research and application value for integrated products such as antennas and structural circuits.

Key words: modified polyetheretherketone, fused deposition modeling, spiral antenna

LIU Dayong, WU Yimin, ZHOU Qiang, GAO Peng, HONG Yuan, LI Zhizhong, ZHOU Wenchao, CAI Chenhao. Integrated Preparation and Performance Study of Spiral Antenna Based on Modified Polyetheretherketone[J]. AEROSPACE CHINA, 2025, 25(3/4): 31-36.

References

[1] CHEN J B, LI Z Z, YANG X H, et al.Micromorphology and thermostability of PEEK/PEI/PES plastics alloys[J]. Asian Journal of Chemistry, 2014, 26(17): 5800-5804.
[2] JI S, YU H, ZHAO J, et al., Mechanical property and machinability study on polyetheretherketone[J]. Optoelectronics and Advanced Materials-Rapid Communications, 2015, 9(1-2): 152-157.
[3] Rong C, Ma G, Zhang S, et al.Effect of carbon nanotubes on the mechanical properties and crystallization behavior of poly(ether ether ketone)[J]. Composites Science and Technology, 2010, 70(2): 380-386.
[4] WANG B, ZHANG K, ZHOU C, et al.Engineering the mechanical properties of CNT/PEEK nanocomposites[J]. RSC Advances, 2019, 9(23): 12836-12845.
[5] Nisa V S, Rajesh S, Murali K P, et al.Preparation, characterization and dielectric properties of temperature stable SrTiO3/PEEK composites for microwave substrate applications[J]. Composites Science and Technology, 2008, 68(1): 106-112.
[6] SUN H, LU Y, ZHANG C, et al.Materials with low dielectric constant and loss and good thermal properties prepared by introducing perfluorononenyl pendant groups onto poly(ether ether ketone)[J]. RSC Advances, 2018, 8(14): 7753-7760.
[7] ZHANG S, WANG H, WANG G, et al.Material with high dielectric constant, low dielectric loss, and good mechanical and thermal properties produced using multi-wall carbon nanotubes wrapped with poly (ether ether ketone) in a p poly (ether ether ketone) matrix[J]. Applied Physics Letters, 2012, 101(1).
[8] Patel P, Hull TR, Lyon R E, et al.Investigation of the thermal decomposition and flammability of PEEK and its carbon and glass-fibre composites[J]. Polymer Degradation and Stability, 2011, 96(1): 12-22.
[9] Kalra S, Munjal B S, Singh V R, et al.Investigations on the suitability of PEEK material under space environment conditions and its application in a parabolic spaceantenna[J]. Advances in Space Research, 2019, 63(12): 4039-4045.
[10] Ahmed S, Bhowmik S.Interpenetrating polymer network adhesive bonding of PEEK to titanium for aerospace application[J]. Journal of Polymer Engineering, 2019, 39(1): 1-9.
[11] Goyal R K, Tiwari A N, Negi Y S.High performance polymer/AlN composites for electronic substrate application[J]. Composites Part B-Engineering, 2013, 47: 70-74.
[12] ZHANG X M, LIU J G, YANG S Y.A review on recent progress of R&D for high-temperature resistant polymer dielectrics and their application in electrical and electronic insulation[J]. Reviews on Advanced Materials Science, 2016, 46(1): 22-38.

ISSN 1671-0940

CN 11-4673/V